Last Updated on September 9, 2021
Updated June 2022: Stop getting error messages and slow down your system with our optimization tool. Get it now at this link
Microsoft’s Windows Media Builder is a useful tool for your computer to download and install the latest version of the Windows 10 operating system. However, you may get the following error message during the installation process:
Operating system security phase: this phase is started to install all necessary updates. Possible causes could be an interrupted download, internet connection, etc.
What causes Windows Update error 0x8007001f – 0x20006?
The error indicates “Operating system security phase”. This phase is triggered to install all necessary Windows updates. Therefore, the possible cause of this error could be an interrupted boot, internet connection, and more.
Although this error can be caused by various factors, its solution should not be too complicated. You can try resetting Windows Update components or clearing the Windows Update cache. You can also temporarily disable the firewall and antivirus program, or run Windows Update in a clean startup state and run the Windows Update troubleshooter.
To start troubleshooting, follow the guidelines below.
How to troubleshoot Windows Update error 0x8007001f – 0x20006?
Perform Windows Update Troubleshooter
Use this tool to identify problems that are preventing Windows from updating.
- Press Windows + R to open the Settings application.
- Go to Update and security -> Troubleshooting.
- In the right pane, select Windows Update and click Run Troubleshooter.
If you’re having problems with Windows Update, the easiest solution is to use Windows Update Troubleshooter, which is a tool built into Windows 10.
Launch Windows Update in clean startup mode
- Make sure you are logged into your computer under an administrator account.
- Type MSConfig in the Run dialog box and click OK to open System Configuration.
- On the General tab, select Selective Run.
- Uncheck Load boot items and make sure the Load system services and Use original boot configuration options are enabled.
- On the Services tab, select the Hide all Microsoft services check box, click Disable all and then click Apply/OK to save your changes.
- Then reboot your computer to put it into a clean startup state.
It’s possible that a particular third-party application or service on your computer is interfering with Windows Update. Instead of spending a lot of time looking for the culprit, you can restart your computer and try to update Windows Update again.
Resetting Windows Update components
- Press Windows + R to bring up the Run window.
- Type cmd and press Ctrl + Shift + Enter to run the command prompt with administrator privileges.
- Enter the following command and press Enter to stop Windows Update components, including the Windows Update service, Encryption service, BITS, and MSI installer.
net stop wuauserv
net stop cryptsvc
net stop bits
net stop msiserver
- Now you need to rename the SoftwareDistribution and Catroot2 folders.
- Simply type the following command line and press Enter each time.
ren C:Windows\SoftwareDistribution SoftwareDistribution.old
- After renaming the folders, you need to restart the above-mentioned affected components.
- Simply enter the following command. Again, don’t forget to press the Enter key after each command.
net start wuauserv
net start cryptsvc
net start bits
net start msiserver
- After resetting the Windows update components, exit the command line and restart your computer.
Expert Tip: This repair tool scans the repositories and replaces corrupt or missing files if none of these methods have worked. It works well in most cases where the problem is due to system corruption. This tool will also optimize your system to maximize performance. It can be downloaded by Clicking Here
Frequently Asked Questions
- Reset the Windows Update components.
- Clear the Windows Update cache.
- Temporarily disable Windows Defender antivirus software and the firewall.
- Run Windows Update in a clean startup state.
This error occurs when users try to update their Windows operating system. It is a system error caused by a corrupted system file.
If Windows 10 Update fails, the most common reasons are as follows: Not enough disk space: If you don't have enough free space on your computer to run Windows 10 Update, the update will stop and Windows will report that the update failed. If you free up some memory, this is usually not a problem.
If you are unable to install Windows 10, it may be due to an interruption in the update process caused by an accidental computer reboot or disconnection from the network. To solve this problem, try installing the program again, but make sure your computer is connected and stays on throughout the process.